Corvettes have long been one of the most popular American-made sports cars. You can see these high-performance vehicles on roads all across the United States as well as countries beyond. In order to drive a C5, you must keep all of the safety features working properly, and that includes making sure the headlights are properly aligned. Luckily, this is a fairly straightforward job and any do-it-yourselfer ought to be able to get it done in an hour or so with the aid of a partner and a screwdriver.

• Led Vs Projector Headlights

Projector Retrofit Kits. Power is nothing without control! Complete projector retrofit kits include all of the components to convert your headlights to a projector-based lighting system for unbeatable performance at night. More difficult?

Step 1

Fill your Corvette with the same amount of weight you would normally carry while night driving. Pay special attention to the trunk and fill the gas tank about half way. Have a friend sit in the driver's seat, as the weight your car carries can greatly affect the angle of the headlight beams over long distances.

Step 2

Park the Corvette about one foot from a large wall with about 30 feet of flat, level ground in front of it. Engage the parking break.

Step 3

Mark the wall with the masking tape along the headlight's axis points. First, take a 6-foot strip of tape and mark from the center point of the passenger's side light across to the middle of the driver's side light. Then take two smaller pieces of tape and put a vertical strip in front of each headlight, creating a cross shape that will act as a bull's eye to aim for.

Sangamam Movie Scenes - Nandu, Silk Smitha First Night Scene. Layanam Malayalam Movie. Sangamam| Movie in Parts 3/9| Silk Smitha, Abhilasha, Devisri. Sangamam Telugu Full Movie - Silk Smitha, Abhilasha, Nandu - V9videos. Layanam - part-2. Silk smitha hot. Tags: Layanam Movies Hot Video Songs, Video, Layanam Movies Hot bollywood movie video, 3gp Layanam Movies Hot video Download, mp4 Layanam Movies Hot hindi movie songs download, Layanam Movies Hot (2015) all video download, Layanam Movies Hot Hd Video Songs, Layanam Movies Hot full song. Layanam cast.

Step 4

Back the Corvette up about 25 feet and turn on the headlights so they shine against the marked wall. Look at how the beams land in respect to the tape. Both headlights should land 2 inches below the long horizontal strip of tape. This will provide adequate light for driving without creating a blind spot right in front of you. Additionally, the passenger's side light should land directly on the shorter vertical strip of tape while the driver's side should land 2 inches to the right. This stops your headlights from blinding oncoming traffic.

Step 5

Open the hood and access the rear of the headlight assembly on the driver's side. Locate the screw on the top center of the headlight which controls the vertical axis. Use a screwdriver to adjust this screw until the light beam hits the desired spot. On the center of one of the sides, find the screw that controls the horizontal beam. Adjust this as well.

Go to the rear of the passenger's side headlight and repeat Step 5. Close hood.

• Jupiterimages/Photos.com/Getty Images

More Articles

Led Vs Projector Headlights

Installing halo projector headlights is fairly simple, but can take a few hours. This is just a general guide for headlights and might vary from your particular set. For all of our headlights, we always recommend professional installation.
Just a few general tips -
1. Wear protective gloves and goggles before working on your vehicle
2. An assistant is helpful when removing the front bumper
3. Put a mat on the floor of your work area to reduce the chances of scratching or harming your lights and/or bumper
4. Do not make direct contact when handling the bulbs or wire assembly until the unit has cooled down. Also avoid any oils on the bulbs.
5. Test the lights prior to installation
Tools and Supplies Required -
1. Diagonal Cutter
2. Ratchet
3. Extension
4. Socket and Combination Wrench
5. Flat head and Philips Screwdriver
..Instructions..
1. Remove the front bumper
2. Remove the connectors from the headlight assembly
3. Remove the five mounting bolts and harness clip, then remove the headlight
4. Remove the bolt and the corner upper beam from the headlight
5. Connect the halo and LED wires to driving lights
a. Connect the black wire to the ground wire (-) of the driving lights
b. Connect the white wire to the positive wire (+) of the driving lights
c. You can also connect the black wire from Halo and LED wires together on the ground wire (-) of the driving light. Connect the white wire from Halo and LED on the positive wire (+) of driving light.
d. Be sure not to damage the resistor during installation.
6. Replace the connectors from the headlight
7. Install the mounting bolts and headlights
8. Install the front bumper
Installation is complete